Inflatable balloon 32 "nose-nose"

ИконкаЛодки в 3D
Add to Compare


Symmetric Inflatable Cylinders

Bothaus with excellent hydrodynamic properties, nose-nose configurations. The inflatable balloon is made of high-quality German PVC fabric, density 750, with edits in the bow and stern and additional protection of the bottom of the balloon. The diameter of the balloon is 32 cm and a small angle of attack on the water, allowing rapid movement with minimal effort. The configuration of the nose-nose balloon causes the lack of exchange stability, excellent germination on the wave and involves the construction of a lightweight catamaran for rapids and mountain rivers.

Inflatable balloons for a catamaran, the length of which can be any - from 3 m to 8 m. Accordingly, the upper platform - from 1 m to 6 m in length. The estimated payload can be calculated as follows: a catamaran with 3-meter cylinders - up to 150 kg, and with 8-meter - to 630 kg. Therefore, each next meter of the catamaran will have a carrying capacity of 96 kg (when the catamaran is drafted 19 cm). But it is better to count when calculating the catamaran is not the maximum load, but 70 to 80 percent of the maximum carrying capacity - then the sediment will be about 16 cm (up to half the balloon), and the germination on the wave is much better. Also consider the possibility to complete inflatable cylinders with extensive additional equipment that will increase the safety and comfort of your vessel.

General Description

     BOATHOUSE inflatable balloons for catamarans, inflatable boats, and kayaks are made from one-piece high-quality PVC fabric made in Germany with a density of 750 and 900. This is a rather complicated and costly method, especially when making large cylinders with a length of 6-8 meters. But thanks to this technology, the cylinder has only one seam, which is located below and is the strongest part, because it has triple fabric (two safety tapes are used - on the top and bottom of the seam). It is almost impossible to break through the balloon in this place (from the bottom of the balloon), taking into account the additional protection of the entire lower part of the cylinders over triple fabric.
     The configuration of the cylinders can be "nose-to-nose" or conventional asymmetric. Nose-nose cylinders can be used to build a catamaran for mountain rivers, where directional stability is not important, and most importantly, good germination on the wave and passability, both front and back. The usual asymmetric form of cylinders is used to build catamarans and trimarans with good directional stability. But the most important thing is that all BOTHAUS cylinders can be considered standard in terms of hydrodynamic indicators - a small angle of attack on water, minimal resistance and excellent germination per wave.
     All cylinders are identical to commercially available models that have different diameters - 32 cm, 38 cm, 42 cm, 45 cm, 50 cm, 55 cm, 60 cm and 65 cm. Thus, 8 types of inflatable balloons in two configurations can be made of any length (from 3 m to 9 m) and with any additional. equipment that will greatly facilitate the task of construction, will create additional amenities and a beautiful appearance.
     Therefore, using BOTHAUS inflatable balloons to build your catamaran or trimaran, you provide your future vessel with excellent technical and operational characteristics, increased safety and reliability. What configuration, what diameter of cylinders and what length is more suitable for you - you will determine this by analyzing the information on our website on a model of a boat with the same diameter of cylinders. If questions arise, our experts will help you make the appropriate calculations.
     Good prices, excellent quality, the correct configuration, and most importantly - excellent hydrodynamic performance - the foundation of any catamaran, will allow you to build a very good boat with excellent speed and driving characteristics.

"Having BOATHOUSE - you live with pleasure."


Inflatable balloon 32 "nose-nose"
Product Code: 32
Brand: Boathouse
Overall dimensions, cm:
Overall dimensions 300-800
Diameter of cylinders, cm:
Diameter of cylinders, cm: 32
Payload, kg:
Payload kg: 200 - 680
The number of pressure compartments, pcs:
The number of pressure compartments, pcs: 1
The weight
Weight of aluminum frame
PVC fabric density:
PVC fabric density: 750
The weight of the platform assembly, kg .:
Weight 3 - 8,5


Write a review
  • This product has a minimum quantity of 2